This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


185 Steering Motor
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Gary(VA) View Drop Down
Silver Level
Silver Level


Joined: 13 Sep 2009
Location: Troutville, VA
Points: 333 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary(VA) Quote  Post ReplyReply Direct Link To This Post Topic: 185 Steering Motor
    Posted: 3 hours 14 minutes ago at 6:42am
Anyone have any tips to change seals in a 185 steering motor. Pulled the cover off from above and wondering what needs to be removed to get to the top seal the easiest. 

Thanks
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20526 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 3 hours 3 minutes ago at 6:53am
 Start by getting a seal kit from AGCO and have it on hand. The steering orbitrol needs to be off the tractor and clamped in a vise. There are 4 lines that need to be disconnected and 4 bolts that hold it to the steering column. The orange panel under the instrument panel has to come off to gain access. Once you have the steering orbitrol in the vise, remove the four small bolts that hold the top on and remove it and remove/replace the quad seal and whatever else is there. Lightly oil the quad seal. DO NOT disassemble any farther !!!!! There will be some parts left over !! Put the top back on a reinstall on the tractor. 

Edited by DrAllis - 3 hours 1 minutes ago at 6:55am
Back to Top
Gary(VA) View Drop Down
Silver Level
Silver Level


Joined: 13 Sep 2009
Location: Troutville, VA
Points: 333 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary(VA) Quote  Post ReplyReply Direct Link To This Post Posted: 2 hours 53 minutes ago at 7:03am
thanks Dr Allis. So no need to remove the instrument panel? 
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20526 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 2 hours 30 minutes ago at 7:26am
Nope. Just the large orange panel below it.
Back to Top
Alvin M View Drop Down
Orange Level
Orange Level


Joined: 24 Jun 2018
Location: PA
Points: 767 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alvin M Quote  Post ReplyReply Direct Link To This Post Posted: 1 hour 32 minutes ago at 8:24am
I do the seal right on the tractor don't need to remove the motor take the bracket that holds the motor to the steering shaft lay with the dash and steering wheel front on the hood then you can pull the cover on the motor and change the seal make sure you hold the shaft in the motor this way you have to take the lines off
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum