IB clutch saga

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have been working on a problem with the clutch on my IB not disengaging. Some of you offered advice before.  I have double checked everything.  I bought another bushing to make certain that it slides easily on the input shaft which it does. It's the same dimension as the one in the flywheel.  The flywheel slides into the shaft and turns easily.  I've polished the shaft end with 600 grit to make sure there is no burr.   The clutch disk slides on the spline easily. There is plenty of travel in the pedal to move the pressure plate fingers the 3/8" necessary. I'm about to reasemble everything and have ordered a tube of SACHS spline grease.   Have any of you used this or similar products and have suggestions? Thanks.

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Freewheeling Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 05 Nov 2017 Location: Wisconsin Points: 152	Post Options Post Reply Quote Freewheeling Report Post Thanks(0) Quote Reply Topic: IB clutch saga Posted: 18 Oct 2024 at 11:44am
	I have been working on a problem with the clutch on my IB not disengaging. Some of you offered advice before. I have double checked everything. I bought another bushing to make certain that it slides easily on the input shaft which it does. It's the same dimension as the one in the flywheel. The flywheel slides into the shaft and turns easily. I've polished the shaft end with 600 grit to make sure there is no burr. The clutch disk slides on the spline easily. There is plenty of travel in the pedal to move the pressure plate fingers the 3/8" necessary. I'm about to reasemble everything and have ordered a tube of SACHS spline grease. Have any of you used this or similar products and have suggestions? Thanks.

Sponsored Links

steve(ill) Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81291	Post Options Post Reply Quote steve(ill) Report Post Thanks(0) Quote Reply Posted: 18 Oct 2024 at 12:56pm
	one thing that can happen is the WICK in the crankshaft -- lubes the bearing area.. can allow excess oil to get on the clutch plates and they DRAG when you push in the pedal.. You have the plates seperated, but the OIL is causing a STICK or DRAG... If the clutch was OIL SOAKED that could be possible problem.. Wash off the clutch with liquid soap and water and make sure all the oil is gone......... IF you had oil on the parts..
	Like them all, but love the "B"s.

Freewheeling Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 05 Nov 2017 Location: Wisconsin Points: 152	Post Options Post Reply Quote Freewheeling Report Post Thanks(0) Quote Reply Posted: 18 Oct 2024 at 1:04pm
	It's a new clutch disk, and pressure plate and the bushing is a new oilite bushing.

AaronSEIA Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 11 Sep 2009 Location: Mt Pleasant, IA Points: 2551	Post Options Post Reply Quote AaronSEIA Report Post Thanks(0) Quote Reply Posted: 19 Oct 2024 at 5:35am
	Didn't install the disk backwards, did you? AaronSEIA