| Author |
 Topic Search  Topic Options
|
SlatWD45 
Bronze Level
Joined: 03 Aug 2024
Location: SE Missouri
Points: 7
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Sealing rims
Posted: 03 Aug 2024 at 3:19pm |
Has anyone put flex seal or spray on bed liner on the inside of a rim to seal it from moisture and the ballast?I just purchased some new rims and want to protect them the best I can.Sorry if this is in the wrong forum.
|
 |
|
Sponsored Links
|
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4742
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Aug 2024 at 6:08pm |
If you never put anything other than air in your tires, The rims will outlast you and your grandchildren's grandchildren. Put anything else in your tires and it won't be IF, your rims rust, but WHEN.
Edited by PaulB - 04 Aug 2024 at 8:45am
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
KJCHRIS
Orange Level
Joined: 21 Dec 2015
Location: WC Iowa
Points: 908
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Aug 2024 at 6:53pm |
There's a product called "coal tar epoxy" available from several commercial paint suppliers. It's used on barges, boats & ships, railroad equipment, in the fertilizer industries and by some DOT's to control rust on snow removal equipment. It comes in 2 parts that mix together to apply. Quart size cans of this mixed and brushed on to the inside of your rims should be rust free for a longtime. Dries to a grayish black color. It requires a bare, clean & rust-free metal surface to be successfully applied. To remove, it takes a sand blaster or use of many grinder discs. Most paints will not stick to it. BUT calcium chloride and sodium chloride (salt water) will not soak into it for a longtime. Use of a respirator or at least a face mask is recommended when using. |
|
AC 200, CAH, AC185D bareback, AC 180D bareback, D17 III, WF. D17 Blackbar grill, NF. D15 SFW. Case 1175 CAH, Bobcat 543B,
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3542
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Aug 2024 at 11:08pm |
|
rims will still 60years with calcuim if you take care of the valve stems and check and fill with the stems on top
|
|
Gary Burnett
Orange Level Access
Joined: 11 Sep 2009
Location: Virginia
Points: 2939
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug 2024 at 4:04am |
 HudCo wrote:
rims will still 60years with calcuim if you take care of the valve stems and check and fill with the stems on top |
If is the key word,I've seen hundreds probably several thousand that Calcium rusted them out.Have also seen where the tube started leaking at other than the valve stem and no way to no until the rust shows up.
|
|
WF owner
Orange Level
Joined: 12 May 2013
Location: Bombay NY
Points: 4666
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug 2024 at 5:44am |
I agree that there are pros and cons to using calcium chloride as ballast.
Personally, I would go to beet juice (Rimgaurd) or windshield washer fluid. Neither are as heavy as CaCl, but both are a lot less corrosive.
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22472
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug 2024 at 6:18am |
IF possible, forget about calcium ! As others have said beet juice,ww fluid. Other possibility is wheel weights. May take 2-3 months to find them ($$$ to ship after all they are HEAVY ). Maybe cast ones using concrete ?
Problem 'painting' the inside of the rim is it'll get scratched when mounting the tire and ANY knick,slice, gouge no matter how small IS where the salt water WILL find and ,ugh, the rim rots..very slowly at first,but, sigh, it's begun......
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
Gary Burnett
Orange Level Access
Joined: 11 Sep 2009
Location: Virginia
Points: 2939
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug 2024 at 6:24am |
jaybmiller wrote:
IF possible, forget about calcium ! As others have said beet juice,ww fluid. Other possibility is wheel weights. May take 2-3 months to find them ($$$ to ship after all they are HEAVY ). Maybe cast ones using concrete ?
Problem 'painting' the inside of the rim is it'll get scratched when mounting the tire and ANY knick,slice, gouge no matter how small IS where the salt water WILL find and ,ugh, the rim rots..very slowly at first,but, sigh, it's begun......
|
Plus only have to buy weights one time and most shops charge a lot extra to deal with fluid
|
|
Leon B MO
Orange Level
Joined: 12 Sep 2009
Location: Old Monroe, Mo
Points: 2111
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug 2024 at 6:16pm |
|
Also be careful how much paint or other substance you apply to the rim. I put two new rear tires on an 8050, the rims were a little rusty so I painted them with a rattle can. It wasn't long after that the tire spun on the rim and cut the stem of the tube. We roughed up the bead and the outer part of the rim and it's been okay ever since.
Leon B Mo
|
|
Uncle always said "Fill the back of the shovel and the front will take care of itself".
|
|
