![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Roto baler table conveyor problem |
Post Reply ![]() |
Author | |
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() Posted: 01 Oct 2023 at 7:58pm |
I tried to get my roto baler working today after sitting for 4 years. The conveyor on the table will not engage.
|
|
![]() |
|
Sponsored Links | |
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8418 |
![]() ![]() ![]() ![]() ![]() |
Welcome to forum
|
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Thanks. I should have included more info. The last time I used it it became clogged up and I couldn't get it free.
Today I finally unclogged it and got the belts spinning but conveyor isn't working. I've tried pulling the rope to get it going. I'm not sure if the twine mechanism needs to be reset or if it is the clutch. Any help would be appreciated. |
|
![]() |
|
PaulB ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4782 |
![]() ![]() ![]() ![]() ![]() |
There is a replaceable wear piece on the dog lever that engages and disengages the pickup conveyor. When it gets rounded it causes problems.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Thanks Paul. I took a picture of the part I think you are talking about but couldn't load it on this page. It has a threaded hole in it like something should go on it.
|
|
![]() |
|
PaulB ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4782 |
![]() ![]() ![]() ![]() ![]() |
Yes: That sounds right. It has a wear pad that bolts on there.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
![]() |
|
dr p ![]() Orange Level ![]() Joined: 24 Feb 2019 Location: new york Points: 1194 |
![]() ![]() ![]() ![]() ![]() |
Before mike finds the part for you, make sure the linksge is free. Stuff loves to set up after 4 years the latch plare could be frozen
|
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Well the conveyor started working so I decided to try a few bales. After going about 100 feet the baler PTO stopped and the tractor died. Basically the same thing that happened 4 years ago. Then I thought the hay clogged it up but now think something else is getting it into bind. Any ideas?
|
|
![]() |
|
dr p ![]() Orange Level ![]() Joined: 24 Feb 2019 Location: new york Points: 1194 |
![]() ![]() ![]() ![]() ![]() |
Are the bale forming belts workly correctly? Sometimes the lower belt get caught by the upper belts . That can stall the tractor
|
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
I will check that tomorrow. Thanks
|
|
![]() |
|
darrel in ND ![]() Orange Level ![]() ![]() Joined: 22 Nov 2009 Location: Hebron, ND Points: 8644 |
![]() ![]() ![]() ![]() ![]() |
There's a brake drum on lower right side. Make sure that the brake shoes aren't rusted to the drum
|
|
![]() |
|
Lars(wi) ![]() Orange Level Access ![]() ![]() Joined: 14 Sep 2009 Location: Permian Basin Points: 7314 |
![]() ![]() ![]() ![]() ![]() |
Use a bigger tractor!!
No, wait don’t do that! |
|
I tried to follow the science, but it was not there. I then followed the money, and that’s where I found the science.
|
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
I did loosen the bolt on the brake before I started but I didn't check to see if the pad was rusted. It ran fine and rolled a partial bale before it locked up.
|
|
![]() |
|
TB63 ![]() Bronze Level ![]() ![]() Joined: 01 Oct 2023 Location: Lawson Missouri Points: 8 |
![]() ![]() ![]() ![]() ![]() |
Hey guys. Thanks for the all the helpful advice. I was able to bale a few today. I took a brass hammer and tapped on the brakes and they popped free.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |