This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Allis drag disk
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
185turbo View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 15 Aug 2018
Location: Kansas
Points: 104 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 185turbo Quote  Post ReplyReply Direct Link To This Post Topic: Allis drag disk
    Posted: 06 Oct 2023 at 12:40pm
I have an Allis chalmers drag disk , I was curious if any one would be able to identify it by model number ect . It has a couple bearings out on the gangs and I figured it may help trying to find parts

185 turbocharged w/ 500 loader , WD
Back to Top
Sponsored Links


Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4724 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2023 at 1:19pm
Right there on the bearing housing is a part number to get you started. 
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
juniorp53 View Drop Down
Bronze Level
Bronze Level


Joined: 16 Mar 2012
Location: United States
Points: 43 		Post Options Post Options   Thanks (1) Thanks(1)   Quote juniorp53 Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2023 at 2:08pm
#9 pull type   bearings are wood  made of  rock maple    most folks make there own    off the top of my head  inner dia is 2" and outside dia is 3 1/2"    soak in hot oil bath  before install then grease initially and after  every few hours of use 

some guy out in Minnesota was advertising he had some NOS ones  talked to him on the phone  wicked nice ... said he would call back with some measurements  ...never did 
Back to Top
185turbo View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 15 Aug 2018
Location: Kansas
Points: 104 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 185turbo Quote  Post ReplyReply Direct Link To This Post Posted: 07 Oct 2023 at 3:22pm
Do you think oak would be any good to make bearings ?
185 turbocharged w/ 500 loader , WD
Back to Top
DON G View Drop Down
Silver Level Access
Silver Level Access
Avatar

Joined: 14 Feb 2014
Location: Lowpoint, IL
Points: 407 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DON G Quote  Post ReplyReply Direct Link To This Post Posted: 07 Oct 2023 at 3:36pm


    I think oak would be good/
Back to Top
Jim.ME View Drop Down
Orange Level
Orange Level


Joined: 19 Nov 2016
Location: Maine
Points: 951 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jim.ME Quote  Post ReplyReply Direct Link To This Post Posted: 07 Oct 2023 at 4:30pm
I think hard maple is better than oak.  It is closer grained and less acidic than oak.  Lignum vitae (iron wood) is the preferred wood for water turbine and ship shaft bearings.  However, it needs to be kept wet even when in storage.  Hard maple was the second choice as it became harder to get Lignum vitae.

For disc bearings hard Maple would likely be better than oak.  It is closer grained and is less acidic than oak.  Maple is often soaked/boiled in hot oil or wax to add to its lubricity further into the wood.   There are several outfits making wood bearings using hard maple.
Back to Top
185turbo View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 15 Aug 2018
Location: Kansas
Points: 104 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 185turbo Quote  Post ReplyReply Direct Link To This Post Posted: 09 Oct 2023 at 7:42pm
Thanks for the info , does anyone know a good place to get the wood bearings?
185 turbocharged w/ 500 loader , WD
Back to Top
juniorp53 View Drop Down
Bronze Level
Bronze Level


Joined: 16 Mar 2012
Location: United States
Points: 43 		Post Options Post Options   Thanks (0) Thanks(0)   Quote juniorp53 Quote  Post ReplyReply Direct Link To This Post Posted: 10 Oct 2023 at 5:54pm

talked to these folks few years back    explained to them over phone what i had and seemed like no problem for them 
Back to Top
Mikez View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 16 Jan 2013
Location: Usa
Points: 8379 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mikez Quote  Post ReplyReply Direct Link To This Post Posted: 10 Oct 2023 at 7:49pm
I think I kept a nos for future measurements.






Edited by Mikez - 10 Oct 2023 at 8:01pm
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.080 seconds.


Help Support the
Unofficial Allis Forum