This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


B starter orientation
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
DMac View Drop Down
Bronze Level
Bronze Level


Joined: 18 Feb 2023
Location: Springville ny
Points: 74 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DMac Quote  Post ReplyReply Direct Link To This Post Topic: B starter orientation
    Posted: 16 Sep 2023 at 7:00pm
I have a starter from an older b with the push rod and starter button on the bottom. Can I rotate the nose on that and use it on a newer b with the pull rod and button on top, and if so what is the procedure?
Back to Top
Sponsored Links


Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81065 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2023 at 7:06pm
YES you can... as you said, take out the two long bolts going all the way thru the starter case.. Dont take everything apart... just rotate the nose 180 degrees relative to the switch and put the bolts back in. .... the GROUND BOLT/ anchor should still be in the right place in the nose.
Like them all, but love the "B"s.
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81065 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2023 at 7:11pm
https://www.youtube.com/watch?v=VpIo-QgudMQ

look here about the 4 minute mark... just dont pull the nose out more than 1/4 inch so the brushes on the BACK dont come out of the holder... DONT take off the back end.
Like them all, but love the "B"s.
Back to Top
DMac View Drop Down
Bronze Level
Bronze Level


Joined: 18 Feb 2023
Location: Springville ny
Points: 74 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DMac Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2023 at 8:48pm
do you just cut that little alignment pin off ?
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81065 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2023 at 9:19pm
there may be a hole on the other side to put it in...  if you look at the movie at 6:15 you can see him slide the armature back into the nose.... So you COULD pull the nose all the way off of the housing and look at the pin, drill a hole, etc.... Just TRY not to pull the rotor out of the back end or you will have to reassemble the brushes..

Not a big deal, but kind of a PITA if you have not done it before..


Edited by steve(ill) - 16 Sep 2023 at 9:25pm
Like them all, but love the "B"s.
Back to Top
DMac View Drop Down
Bronze Level
Bronze Level


Joined: 18 Feb 2023
Location: Springville ny
Points: 74 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DMac Quote  Post ReplyReply Direct Link To This Post Posted: 17 Sep 2023 at 8:11am
ok ill give it a try thank you!
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.080 seconds.


Help Support the
Unofficial Allis Forum