This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


F2 motor into a d19.
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Valleyfarmanddiesel View Drop Down
Bronze Level
Bronze Level


Joined: 10 Aug 2022
Location: Mn
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Valleyfarmanddiesel Quote  Post ReplyReply Direct Link To This Post Topic: F2 motor into a d19.
    Posted: 12 Aug 2022 at 2:29pm
Has anyone on here replaced a d19 gas motor with a gleaner f2 motor? Having trouble with the starter. Not sure if I need to swap ringgears, starters or if it's even possible. Had to use the gas flywheel that is set for a 9 tooth small drive and the f2 is set for a 10 tooth 40mm drive. Let's just say the ten engages but locks her up tight. I am finding this was a bad idea but am stuck finishing it.
Back to Top
Sponsored Links


Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 12 Aug 2022 at 9:27pm
I would bet (Steve In NJ) on here can fix you up with the right drive.                  MACK
Back to Top
Valleyfarmanddiesel View Drop Down
Bronze Level
Bronze Level


Joined: 10 Aug 2022
Location: Mn
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Valleyfarmanddiesel Quote  Post ReplyReply Direct Link To This Post Posted: 15 Aug 2022 at 9:09pm
Going to pull the motor again and see if I can swap the ring gears. Hope I works. Went to a couple starter shops and no luck. Tried to look up Steve in NJ but no luck. Thanks mack
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 88406 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 15 Aug 2022 at 9:17pm
Steve might not be able to FIX... but he sure could fill you in on possibilities...





Edited by steve(ill) - 15 Aug 2022 at 9:21pm
Like them all, but love the "B"s.
Back to Top
8070nc View Drop Down
Orange Level Access
Orange Level Access


Joined: 21 Mar 2019
Location: North Carolina
Points: 637 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 8070nc Quote  Post ReplyReply Direct Link To This Post Posted: 15 Aug 2022 at 9:19pm
B&b custom circuits on the web
1984 80780
1957 D14
DES 300 with 25000 engine
616 tractor
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.059 seconds.


Help Support the
Unofficial Allis Forum