| Author |
 Topic Search  Topic Options
|
elec 
Bronze Level
Joined: 23 Nov 2020
Location: mi
Points: 86
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 62 d17 governor?
Posted: 04 Sep 2021 at 9:38am |
|
Was driving my D17 on the road the other day and the engine revved to about 500 RPMs above normal. Now, sitting still,at half throttle, engine is running at full speed. My dad thinks it is the governor. Any input would be appreciated before we tear it apart.
Thank you
|
 |
|
Sponsored Links
|
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 87587
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2021 at 12:23pm |
Ii would not start motor again... pull front and look at governor
|
|
Like them all, but love the "B"s.
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8612
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2021 at 3:28pm |
|
Should be able to remove cover at front of governor and peek in at weights. Don't have to tear whole front off to have a look.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21832
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2021 at 4:21pm |
|
You may be lucky and have only broken one governor weight and not damaged anything else, YET. DO NOT start it or crank it over !!! Remove distributer cap, mark exactly where the rotor tail is pointed and pull out the governor/.distributer all in one piece. Once repaired reassemble making sure the rotor tail is EXACTLY pointed where it was before and you're good-to-go.
|
|
DonBC
Orange Level Access
Joined: 12 Sep 2009
Location: Courtenay, BC,
Points: 944
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2021 at 6:00pm |
|
Replacing pins and weights is at lot simpler and less costly than having an engine throw a rod when it takes off.
|
|
Jack of all trades, master of none
|
|
elec
Bronze Level
Joined: 23 Nov 2020
Location: mi
Points: 86
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2021 at 7:29pm |
Thanks. Will push it in the garage and get it fixed. And I'll tell my dad he was right. 
|
|
Oldwrench
Bronze Level
Joined: 12 Jan 2020
Location: Northeast
Points: 151
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Sep 2021 at 8:50am |
|
The Dr. and others have mentioned several times to change the governor weights and pins as a PM. Is there any indication or typical hours to indicate when the engine should have the governor serviced? My D17 IV had the engine rebuilt at ~ 3,000hrs at an AC dealership with a top notch mechanic, and it still runs like a top 20 years later with only an additional 1,000 hrs. However, I have no idea if they would have replaced the weights as a matter of course. Now I am wondering if I shouldn't dig into it just to be safe. Any guidance on when to PM the governor or any warning signs of impending failure?
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21832
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Sep 2021 at 7:22pm |
|
Governor weights work just fine until they break/explode.
|
|
Lon(MN)
Orange Level
Joined: 11 Sep 2009
Location: Merrill Wi
Points: 2032
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2021 at 6:54am |
|
I just put a D17 on the shelf because of this. Weights came off, took out the governor gear, broke several teeth on the camshaft, and bent some teeth on the crankshaft.
|
|
