This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
AC720 limited power and backfiring |
Post Reply |
Author | |
healinggreenfarms
Bronze Level Joined: 21 Jun 2021 Location: Raleigh, NC Points: 9 |
Post Options
Thanks(0)
Posted: 21 Jun 2021 at 7:46am |
Hello all!
I tried searching the forum and didn't see exactly what I'm experiencing, although perhaps I don't know the correct lingo. Reba is a '78 720. Relatively new transmission. Working great and then in the middle of a job lost *almost* all power to the wheels. Front and rear PTO working fine. If I jostled the gear selector I could get her to move a little. We limped back to the shelter, BARELY making it up a little hill. Same problem after I let her rest for a few days. Now, when ever she is shut down she shudders then backfires. Any thoughts? Thanks!
|
|
Sponsored Links | |
Acdiesel
Orange Level Joined: 15 Jun 2012 Location: Rochester Ohio Points: 2550 |
Post Options
Thanks(0)
|
so, the engine starts and runs at an idle and if you try to give it any throttle it looses power and back-fires??
check the breaker points gap- also a failed condenser will give you the same issue.
|
|
D19 diesel,D17 diesel SER.3 D14 NF,D14 WF, D15 SER.II wf
D15 SER.2 DIESEL,D15 ser.II nf D12 SER.I, D10 Ser.II 2-720'S Gmc,caterpillar I'm a pharmacist (farm assist) with a PHD (post hole digger) |
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4944 |
Post Options
Thanks(0)
|
Points and timing is a good place to start but before you do that, see if your getting adequate fuel through the clear fuel filter if you have one. Fuel pump may be going bad and if enough fuel isn’t getting to the carb it will cause the same issue. Mine did it last weekend and I am now deciding if I’m going to rebuild the pump or put an electric pump on it. I like staying factory but the fuel pumps are problematic. Have also had a bad fuel cap do the same thing, but if it sits for a half hour it would run again just fine for a few minutes until it began creating a vacuum and start sucking the tank in from the sides and die. The vent goes bad in the cap, no cleaning I did resolved it. So I replaced both of mine with a cap that has a fuel gauge which makes it nice to get a quick visual of the level of fuel in the tank.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
farmtoybuilder
Orange Level Joined: 11 Sep 2009 Location: Dresden,Ohio Points: 1454 |
Post Options
Thanks(0)
|
Stick a Kubota 3 Cylinder diesel in it! :) Onan motors in them were a pain!
|
|
5 different TT-10's,5 TT-18's Terra Tigers,B-10,2 B-207's,B-110,2 B-112's,HB-112,B-210,B-212,HB212,2 Scamp's & Homilite T-10. Still hunting NICE HB-112 & anything Terra Tiger & Trailers for them.
|
|
PaulB
Orange Level Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4775 |
Post Options
Thanks(0)
|
ONANs are known for having valve seats come loose: check compression.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4944 |
Post Options
Thanks(0)
|
After reading this again, is the engine running ok, except for the backfire, is this a hydro problem? Does the engine run fine but as you move the hydro lever forward is the tractor just not moving? Need some more info
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4944 |
Post Options
Thanks(0)
|
Update?
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4944 |
Post Options
Thanks(0)
|
My 720 acted up again yesterday, back firing and started loosing power. Mixture screw on the bottom of the bowl backed out again. Need to put some pipe tape on the threads this time. Apparently the packing isn’t keeping it tight.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
dee_veloper
Orange Level Joined: 12 Apr 2021 Location: USA Points: 1168 |
Post Options
Thanks(0)
|
I know of 3 things which cause backfiring
. 1) A timing problem 2) Sticking valves that aren't closing 3) excess fuel detonating in a hot exhaust. Check the valves to make sure they are opening and fully closing I don't know what type of ignition system you have but if points, check they are in good condition and gapped correctly. If you have an ignition module it may need to be replaced If you have a carb. then check the fuel air mixture setting to make sure you aren't running rich |
|
Don't confuse my personality with my attitude.
My personality is who I am. My attitude depends on who you are. |
|
talntedmrgreen
Silver Level Joined: 25 Jun 2013 Location: Caledonia, MI Points: 477 |
Post Options
Thanks(0)
|
9 times out of 10, the backfiring ont hese is timing. The points box loosens, and moves...the issue can come, go, worsen, cure itself, then come back, as the points box shifts around. It's easy to press on the points box left or right, and see if the condition goes away or worsens, and then you have your answer. Timing is really pretty easy to set on these.
|
|
Patterson B1*B1/B1Forklift*B10*BigTen/B1Loader*B110*B208*B206*616*Homelite T16H/T8/T7/RM7E*Landlord/Loader/Trencher*Broadmoor717*Serf525*2110*7790*Legacy XL*Twin 20*Squire9*Squire6*JCPenny 494
|
|
talntedmrgreen
Silver Level Joined: 25 Jun 2013 Location: Caledonia, MI Points: 477 |
Post Options
Thanks(0)
|
I just combatted this, this morning, on a 4041 I brought home last week. A minor points tweak solved the backfire and a carb adjustment put the fuel mixture where it needed to be for full power. Brought this thing home, after dragging it out of the spot it sat for over 30 years. The last oil change date was '89. Runs like a top!
|
|
Patterson B1*B1/B1Forklift*B10*BigTen/B1Loader*B110*B208*B206*616*Homelite T16H/T8/T7/RM7E*Landlord/Loader/Trencher*Broadmoor717*Serf525*2110*7790*Legacy XL*Twin 20*Squire9*Squire6*JCPenny 494
|
|
AC-DVB
Bronze Level Joined: 11 Apr 2021 Location: Manitoba Points: 15 |
Post Options
Thanks(0)
|
Thats an awesome find, keep them alive!!
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |