| Author |
 Topic Search  Topic Options
|
shaun44 
Bronze Level
Joined: 12 May 2019
Location: pennsylvania
Points: 6
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: allis 653
Posted: 10 Apr 2020 at 9:46am |
|
hey all first post but not really to new lol. restoring a 653. have reverse no forward. pulled filter ya it was full of sludge lol,changed fluid, good flow off the pump, no leaks, pressure going to shuttle is zero in forward and 150 at idle and higher rpm's when warm (below spec) swapped the valve just because and got the exact same results.swapped lines around also for giggles lol. So shuttle clutch is bad no big deal. Just looking for new parts? Agco still have this stuff still available? This seems to be the hard part haha. I dont seem to find any aftermarket stuff out there. Any hellp is greatly appreciated Thanks Shaun
|
 |
|
Sponsored Links
|
|
|
Randaleky
Silver Level
Joined: 17 Aug 2011
Location: belfry, ky.
Points: 427
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2020 at 12:24am |
|
welcome to the forum. I am from eastern Ky. and I have a HD4 dozer.
|
|
shaun44
Bronze Level
Joined: 12 May 2019
Location: pennsylvania
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Apr 2020 at 4:27pm |
|
o wow the hd4 is really similar so i hear. This is my first attempt at a restore on a allis chalmers bulldozer looked like i picked a real winner but its fun to me and seems like a simple unit. I pulled the engine the other day in about 2 hours not a bad job at all. have the shuttle out and waiting on a parts manual since the internet has all but failed me lol. Im not to far from sandy lake equipment. i see they do some advertising here and also im not far from stephenson equipment they have pages and pages of part numbers and parts on stock, i guess i just need the parts manual. owell glad to be hear and there is a wealth of knowledge from what i see
|
|
Randaleky
Silver Level
Joined: 17 Aug 2011
Location: belfry, ky.
Points: 427
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Apr 2020 at 1:28am |
|
yes a lot of experience to answer post. feel free to post , someone will have an answer for you.
|
|
pinball
Orange Level Access
Joined: 28 May 2014
Location: missouriu
Points: 6408
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Apr 2020 at 9:55am |
|
randall hope your staying safe. does the 653 and h4 use the same clutch pack.
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 42018
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Apr 2020 at 9:39am |
653/655 and the H4 share all the same parts well except drive clutch operation as one was pedal steer other had steer to clutch packs . Support roller tower on track changed from inside to outside position on track frame also but uses same roller
Edited by Coke-in-MN - 29 Apr 2020 at 9:41am
|
|
Life lesson: If you’re being chased by a lion, you’re on a horse, to the left of you is a giraffe and on the right is a unicorn, what do you do? You stop drinking and get off the carousel.
|
|
Randaleky
Silver Level
Joined: 17 Aug 2011
Location: belfry, ky.
Points: 427
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 May 2020 at 12:01pm |
|
Hey Norman, I am doing fair , How are you ? PM me when you get time . Lot to tell you but this is not right post for that
|
|
pinball
Orange Level Access
Joined: 28 May 2014
Location: missouriu
Points: 6408
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 May 2020 at 7:49am |
|
hey randall. did you get my message
|
|
