| Author |
 Topic Search  Topic Options
|
Levibridge95 
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis chalmers b final drive
Posted: 17 Aug 2019 at 9:10pm |
|
Hey. I'm a new member here and I'm currently rebuilding a '51 AC B. I broke my left final drive trying to remove the shaft to replace bearings. I have a spare one I'm buying to replace it. Any tips on removing the shaft without breaking the final drive casing? Which way do you press? Thanks.
|
 |
|
Sponsored Links
|
|
|
Jim.ME
Orange Level
Joined: 19 Nov 2016
Location: Maine
Points: 952
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 Aug 2019 at 9:26pm |
|
Welcome to the forum.
Which shaft were you trying to pull, pinion or axle?
I expect Gerald will post a link to the manual (it covers the G, B, C, and CA models) he has on line, when he sees your post. Down load and save a copy so you have it. That will give you the info you need and the tools to do the job. Easier if you read it first. Folks here will give you a hand if you have questions about the procedure.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 Aug 2019 at 9:44pm |
|
the bull shaft comes out pretty easy after the remove the snap ring on the bull gear / shaft.... the top axle shaft is really not stuck in the case, it is "normally" the brake hub that is stuck to the shaft... There is a lock screw on the hub.. access thru the 1 inch round hole in the case.. You might head the brake hub.. soak with penetrant, etc... Many are HARD to get off. some have broken the brake drum to get the shaft out. I have never heard of the CASE breaking... I set the base on the end with shaft sticking straight up.. press the shaft OUT from the INSIDE to the OUTSIDE ... and it moves thru the drum as you push........ service manual shows a puller with rods you connect to the drum, then portapower the shaft thru ........ I have also beat them out with a 5 pound hammer and brass plate, but you can distort the splines that slide into the differential if you pound too much...... small grinder can then fix it up.
|
|
Like them all, but love the "B"s.
|
|
Levibridge95
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 Aug 2019 at 9:50pm |
|
Ok thanks. Maybe that's where I went wrong. Instead of pressing inside out, I went outside in thinking it would work. I have the hub stuck on the other final drive axle that i can't get off. It has the one big nut in the middle. Any ideas?
|
|
Jim.ME
Orange Level
Joined: 19 Nov 2016
Location: Maine
Points: 952
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 5:38am |
Here is a link to the factory service manual. You can down load and save it. It is in sections for the different tractors. You need to review pages 36 through 38 in the B, C section for this project. That will help you with nomenclature and sequence. Do you have the final off the tractor? Be sure you tell which shaft, etc. you are working on. Folks will help you with your questions from there. G, B, C, CA service manual
|
|
Dick L
Orange Level
Joined: 12 Sep 2009
Location: Edon Ohio
Points: 5087
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 7:07am |
|
|
|
Dick L
Orange Level
Joined: 12 Sep 2009
Location: Edon Ohio
Points: 5087
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 7:47am |
|
You might want to tell exactly how and where the final drive broke. What all lock screws and nuts you had removed would also help us help you.
|
|
Gerald J.
Orange Level
Joined: 12 Sep 2009
Location: Hamilton Co, IA
Points: 5636
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 11:37am |
|
|
|
Levibridge95
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 12:43pm |
|
It was the pinion shaft. I removed all the bolts and nuts. It broke on the inside part between the brake drum and the gear. That bearing in the middle. Thanks for the help so far.
|
|
Dick L
Orange Level
Joined: 12 Sep 2009
Location: Edon Ohio
Points: 5087
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 3:07pm |
|
Were you pressing on the spline shaft that goes into the transmission?
|
|
Bill Long
Orange Level
Joined: 12 Sep 2009
Location: Bel Air, MD
Points: 4556
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 3:12pm |
Levibridge95, Welcome the the Unofficial Allis-Chalmers Forum. As shown above you will receive a warm welcome and LOTS of outstanding help.
I cannot add to what has already been said only to say, Take good care of my favorite Allis Chalmers Tractor. Sounds like you are doing a GREAT JOB!
Good Luck! Bill Long
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 4:42pm |
Ok thanks. Maybe that's where I went wrong. Instead of pressing inside out, I went outside in thinking it would work. I have the hub stuck on the other final drive axle that i can't get off. It has the one big nut in the middle. Any ideas? To get the hub off the bull shaft, I remove the nut and soak with penetrant... Smack the hub and 3 oclock and 9 oclock alternately to try to rock it on the shaft.. Normally it will pop off... If not, you can use a puller... Get a couple 3/4 inch all thread and put thru the holes in the hub with nuts on the back.. they should be sticking out parallel to the bull shaft....... you need a BIG plate or bar an inch or better thickness to go across the shaft and have the althread sticking thru the bar on each side... tighten the nuts on the althread until the bar starts to bend or you can't get any tighter... THEN smack the hub on each side with a 20# hammer.
Edited by steve(ill) - 18 Aug 2019 at 4:53pm
|
|
Like them all, but love the "B"s.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 4:49pm |
Ok thanks. Maybe that's where I went wrong. Instead of pressing inside out, I went outside in thinking it would work. I have the hub stuck on the other final drive axle that i can't get off. It has the one big nut in the middle. Any ideas? Set the axle housing in the press or on a couple of wood blocks so it is LEVEL and the differential end ( splined shaft) pointing UP... See DICKS picture of the press... The press is the way to go.. You can BEAT it out, but check splines for minor distortion after the shaft is out... You are trying to push the shaft THRU the brake drum... There is a SET SCREW in the hub !! get it out first... Soak with penetrant... maybe some heat.
|
|
Like them all, but love the "B"s.
|
|
Levibridge95
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 8:51pm |
|
Yes
|
|
Levibridge95
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Aug 2019 at 8:52pm |
|
Thank you
|
|
Levibridge95
Silver Level
Joined: 23 Jan 2018
Location: Quakertown Pa
Points: 69
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 Aug 2019 at 7:05pm |
 steve(ill) wrote:
Ok thanks. Maybe that's where I went wrong. Instead of pressing inside out, I went outside in thinking it would work. I have the hub stuck on the other final drive axle that i can't get off. It has the one big nut in the middle. Any ideas? To get the hub off the bull shaft, I remove the nut and soak with penetrant... Smack the hub and 3 oclock and 9 oclock alternately to try to rock it on the shaft.. Normally it will pop off... If not, you can use a puller... Get a couple 3/4 inch all thread and put thru the holes in the hub with nuts on the back.. they should be sticking out parallel to the bull shaft....... you need a BIG plate or bar an inch or better thickness to go across the shaft and have the althread sticking thru the bar on each side... tighten the nuts on the althread until the bar starts to bend or you can't get any tighter... THEN smack the hub on each side with a 20# hammer.
|
I suspended the final drive with my engine hoist by putting a strap on the hub and lefting it in the air a couple inches. Then i firmly tapped on the axle itself till it slide out. Thanks for the help everyone. Slowly getting the tractor back together. Couldn't remove the set screws so i had to cut off the steering arms and the spindles then slid out.
|
|
