| Author |
 Topic Search  Topic Options
|
Ted in NE-OH 
Orange Level
Joined: 12 Nov 2009
Location: Austinburg OH
Points: 1703
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: D-10, D-12 Light parts needed
Posted: 02 Jan 2019 at 6:04pm |
I need the following parts for a late model D10, D12
Cast bracket that mounts to the RIGHT fender under the
forward facing light.
Cast bracket that mounts to the right fender under the REAR
facing light
Light, forward facing fender light.
Note: these parts may be common to D14, D14
Please respond via e-mail with price and condition of part actcseifert@hotmail.com
|
|
CA, WD, C, 3 Bs, 2 Gs, WC, I-400, 914
|
 |
|
Sponsored Links
|
|
|
tbird
Bronze Level
Joined: 01 Nov 2013
Location: usa
Points: 137
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jan 2019 at 6:12pm |
|
djs tractor parts have them fits d 10 through d19 at 45.00 each phone no 734 320 3470
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7530
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jan 2019 at 8:16pm |
D14 Does not use them - headlights are on the grille shell. However, D15 Series II, D17 Series III and IV and the D19 use the same headlights and mountings. They are hard to find used though. As mentioned above your best bet is to get new repros from DJs or one of the other vendors here.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '63 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 5157
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2019 at 1:18am |
|
I have those light bases avalable, $20 each plus the shipping.
I’ll have to wait until I get home to add the picture
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
Dave H
Orange Level
Joined: 11 Sep 2009
Location: Central IL
Points: 3591
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2019 at 3:58am |
Way back when i was in the same boat. Got a casting from DJS.
As I foggily recall it was right dimentionally but yes a ROUGH casting that required some working down.
So depending on the price, i would go for the used if the price was right comparatively. Just a thought.
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 5157
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2019 at 11:30am |
Here is a picture of the light bases I have available. The castings I get are very good quality, I have them casted by the Amish, not from China. Unfortunately the picture is a bit fuzzy
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
