MY HD4 DILEMMA

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Removed the sprocket axle from my right side. seal was bad. outer bearing looks to have a little wear so I will replace it. Case looks good. inner bearing looks good but probably will replace it. The bad is theres pretty good groves wore into the axle where the seal rubs. having never seen an axle I would suspect it should be smooth. looks as though I need another axle so if any of you on here has one just email me. Also is there way I can have it machined down and maybe  sleeve put on it. I don't know what size the shaft where the seal rubs is suppose to be. just trying to see what options I have. all help appreciated. thank 

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
pinball Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 28 May 2014 Location: missouriu Points: 6380	Post Options Post Reply Quote pinball Report Post Thanks(0) Quote Reply Topic: MY HD4 DILEMMA Posted: 01 Aug 2018 at 9:10am
	Removed the sprocket axle from my right side. seal was bad. outer bearing looks to have a little wear so I will replace it. Case looks good. inner bearing looks good but probably will replace it. The bad is theres pretty good groves wore into the axle where the seal rubs. having never seen an axle I would suspect it should be smooth. looks as though I need another axle so if any of you on here has one just email me. Also is there way I can have it machined down and maybe sleeve put on it. I don't know what size the shaft where the seal rubs is suppose to be. just trying to see what options I have. all help appreciated. thank

Sponsored Links

Tracy Martin TN Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 11 Sep 2009 Location: Gallatin,TN Points: 10756	Post Options Post Reply Quote Tracy Martin TN Report Post Thanks(0) Quote Reply Posted: 01 Aug 2018 at 9:22am
	Try a Speedi Sleeve. It should work. HTH Tracy
	No greater gift than healthy grandkids!

Ages Cat Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Sep 2009 Location: Hutchinson, MN Points: 700	Post Options Post Reply Quote Ages Cat Report Post Thanks(0) Quote Reply Posted: 01 Aug 2018 at 3:15pm
	Second on the speed sleeve.
	Curt Anderson HD3, HD5B, HD6AG,HD6B dozer, I-400,615, 616,620,720,ACP25 lift truck, 1956 D Grader, AC 540 loader, AC #84 plow, Simplicity tractors, Agco MT225, Agco 2025,

orangeman Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Sep 2009 Points: 1852	Post Options Post Reply Quote orangeman Report Post Thanks(0) Quote Reply Posted: 01 Aug 2018 at 3:24pm
	Ok Norm - per the description in the post - " pretty good grooves" does this mean that the axle has been compromised to a point that its tensile strength is in question? Is the axle worn to a point where it could be fracture critical if the design load against it would cause it to fail? While speedy sleeve have their place, am wondering if grooves are such that a new or good used would be an option to consider for the subject repair? Good Luck... Orangeman

pinball Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 28 May 2014 Location: missouriu Points: 6380	Post Options Post Reply Quote pinball Report Post Thanks(0) Quote Reply Posted: 01 Aug 2018 at 4:16pm
	I took it to the local fab shop and they said they could turn it down and sleeve it. cost 120 bucks. I think I am going to have it done on this one. I am concerned about integrity of it also. In the mean time the fellow from zimmermans called and said they had some. I went down to look and I found one from a 655 that s in pretty nice shape so I bought it after we haggled on the starting price of 375 and e came down considerably but he had 6/7 axles. I don't think there are to many dummys besides me wanting parts for an hd4. prices were stupid. allis wanted 1500 for a new one, others wanted 6-8 hundred for a used one. did find a new after market for 600. im liven, learning and going broke . o well theres another day. thanks to you all. now I have to find a seal. allis wants 135 for theres. May just have to put some rope in there and say the heck with it. Have a good day to all.