![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
WTB Emulsion tube/discharge jet |
Post Reply ![]() |
Author | |
ekjdm14 ![]() Orange Level Access ![]() Joined: 20 Aug 2024 Location: Manchester UK Points: 771 |
![]() ![]() ![]() ![]() ![]() Posted: Yesterday at 5:54am |
Looking for an emulsion tube (also called "main discharge jet") to replace the broken one in my B's carb.
It's the Zenith carb, on a 125 engine & the emulsion tube is originally a 45-2 although anything that'll fit ought to be better than the broken one which requires running at 90% choke! Thanks, Dan
|
|
Stuck Farmer
|
|
![]() |
|
Sponsored Links | |
![]() |
|
PaulB ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4940 |
![]() ![]() ![]() ![]() ![]() |
I have a bin full of carburetor parts. There were may different versions use in the various Zenith carburetors. If you could make it over to this side of the pond you could possibly match up what you need.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
![]() |
|
ekjdm14 ![]() Orange Level Access ![]() Joined: 20 Aug 2024 Location: Manchester UK Points: 771 |
![]() ![]() ![]() ![]() ![]() |
Thanks Paul, not much chance of me getting over there any time soon sadly, much as I'd love to. Can get a photo of the item needed if it's any help.
Carb I believe is a 61 AJ7 (part #211955, outline #9805)
|
|
Stuck Farmer
|
|
![]() |
|
ekjdm14 ![]() Orange Level Access ![]() Joined: 20 Aug 2024 Location: Manchester UK Points: 771 |
![]() ![]() ![]() ![]() ![]() |
Further to this & with thanks to Mike Z, I believe the 45 jet from a later carb won't fit as the threaded portion is directly under the hex whereas my 45-2 is threaded on the lower end away from the hex.
Will get a photo next time we're over with the tractor but fear this is going to limit my options further.
|
|
Stuck Farmer
|
|
![]() |
|
PaulB ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4940 |
![]() ![]() ![]() ![]() ![]() |
Yes: To get the correct part, I would need to almost have it here to see what I have in the parts bin. just a part number would not be any help.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
![]() |
|
ekjdm14 ![]() Orange Level Access ![]() Joined: 20 Aug 2024 Location: Manchester UK Points: 771 |
![]() ![]() ![]() ![]() ![]() |
That's my fear, these old Zenith carbs look so simple and so "samey" at a glance (And I've seen folk have luck with "put togethers" of multiple broken ones) but when you get into them deeper there's a lot more variation.
Will give it a measure as well as photo when I next lay hands on it. If you have anything that looks similar available to sell at that point I may just chance it since the carb is essentially useless as it sits. Only other timely & practical option being this side of the pond is a Scamazon copy carb which I'd like to avoid, much rather send money to the US than China
![]() Edited by ekjdm14 - 5 hours 1 minutes ago at 10:12am |
|
Stuck Farmer
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |