This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


HD6-B Tensioner Screw Thread Size
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
jwoods View Drop Down
Bronze Level
Bronze Level


Joined: 12 Jan 2014
Location: Oakwood, OH
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jwoods Quote  Post ReplyReply Direct Link To This Post Topic: HD6-B Tensioner Screw Thread Size
    Posted: 25 Jul 2021 at 1:36pm
Hello All,

Had to cut out the old threaded tensioner (22-3/4 length), heat the yoke and extract the threaded portion.  

Two options so far:  

1: Find a boneyard donor

2: Find the correct thread/pitch bolt and weld onto the remaining hex stem. 

 Looks like 1-5/8 x 5.5 pitch, but figured would throw it out here; also if anyone has a source for either.

Thanks, -Joe
Back to Top
Sponsored Links


Back to Top
AC Mel View Drop Down
Orange Level Access
Orange Level Access


Joined: 23 Jan 2010
Location: N.Ca.
Points: 1101 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC Mel Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2021 at 9:25pm
We might have what you need....we're a long ways away...California. Hector...(gemdozer)...will probably be able to help you.  He's got access to a lot of those parts. He'll see the post. 
Back to Top
jwoods View Drop Down
Bronze Level
Bronze Level


Joined: 12 Jan 2014
Location: Oakwood, OH
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jwoods Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jul 2021 at 5:23am
THanks Mel, and...you are correct.
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41614 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 07 Aug 2021 at 12:25pm
I turned a length of stock to thread - then welded it to the end of the hex part on a HD5B  - the lock collar was bad though so had to find a nut to fit end of new turned thread .
 If I were to do it again I would find a hydraulic ram and make it a grease type adjuster . 
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
jwoods View Drop Down
Bronze Level
Bronze Level


Joined: 12 Jan 2014
Location: Oakwood, OH
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jwoods Quote  Post ReplyReply Direct Link To This Post Posted: 08 Aug 2021 at 7:09am
Thanks All,

I was able to find a used replacement screw.  
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum