This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Breaking in a rebuilt 7060
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Topic: Breaking in a rebuilt 7060
    Posted: 31 Jan 2019 at 3:39pm
Just got done rebuilding the engine in my 7060 and getting ready for it's first start and was wondering what you guys do to break in a newly rebuilt engine? Go my break in oil ect, any certain rpm to run it at while letting it get to operating temp to check for leaks etc?
Back to Top
Sponsored Links


Back to Top
Michael V (NM) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: NM
Points: 2483 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Michael V (NM) Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jan 2019 at 5:21pm
My thoughts are, put the oil your gonna run in it, after all is re-torqued , leaks checked,run it up to operating temperature good couple hours then change oil, this ought to get it cleaned up good
do not jus run a light load, but put a decent pull on it for at least the first 100-150hrs.
Back to Top
injpumpEd View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Walnut IL
Points: 5110 		Post Options Post Options   Thanks (0) Thanks(0)   Quote injpumpEd Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jan 2019 at 6:50pm
using break in oil is a good think now days. Regular oil you'll be using is actually too good, and won't let it "wear in". Another thing to do is get it up to temp by putting cardboard over radiator, and once warmed up, drive it around and load it with the brakes a few times. Doing this a few times will help seat everything. Once it's been run an hour or 2 like this, putting it on the dyno would be a great way to put partial load on it. If no dyno, hook it on to something and take it to the field. 
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
Back to Top
skateboarder68 View Drop Down
Silver Level
Silver Level


Joined: 29 Jan 2011
Location: Keota, IA
Points: 372 		Post Options Post Options   Thanks (0) Thanks(0)   Quote skateboarder68 Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jan 2019 at 9:10pm
I wouldn't let it idle much at all. Put it to work for a couple hours. 75% load roughly. Just my opinion I'm no mechanic.
Orange & Silver still earnin their keep on the farm: R62, Series IV D17 nf, 185, 6080, 6080 fwa, 220, 1968 D21, 7045, DT240.
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jan 2019 at 9:14pm
Get water up then put it to hard work.      MACK
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29817 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 01 Feb 2019 at 6:23am
What Mack said................ and watch your temp gauge. After my brother had his 7030 overhauled we put it on a 4x18 plow in alfalfa sod and plowed 10 acres and then it pulled a 20 foot disk and a 6 row 5100 planter and a 9 shank chisel and we used John Deere break-in oil, I think for the first 50 hours. For my small operation that took almost a year to put on the 50 hours especially since I still used my 7050 and 190.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
NEVER green View Drop Down
Orange Level Access
Orange Level Access


Joined: 28 Feb 2013
Location: MN.
Points: 8615 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NEVER green Quote  Post ReplyReply Direct Link To This Post Posted: 01 Feb 2019 at 9:48am

Allis recommends no LUGGING or full sustained loads for first 50hrs.
2-8050 1-7080 6080 D-19 modelE & A 7040   R50       
Back to Top
Unit3 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Oct 2009
Location: NC Iowa
Points: 5603 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Unit3 Quote  Post ReplyReply Direct Link To This Post Posted: 01 Feb 2019 at 10:36am
Not apples for apples, but years back I bought a new Honda 750. Salesman told me to run it at different RPM's for the first 500 mile. It will help seat the rings. ??????? 
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22024 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 01 Feb 2019 at 8:10pm
I toured the Harvey Factory back in 1980. Can't tell you for sure all the engine dyno details because we were moving right along thru the whole place. I'd imagine no more than 1 hour was allotted for each engine performance test. Probably 5 minutes of warm up (coolant water may have already been warm) and then work up to 100% load for a period of time to insure the engine would make and maintain proper HP and oil pressure and have no leaks or any other issues. When I dyno bare engines at work, I run them for 1 hr from initial fire-up to cool-down idle and then shut down. It usually takes me a couple hrs to get an engine connected and another 2 hrs to disconnect. Some engines take me the whole day if there are any leaks or other problems. A-C's connect/disconnect time would have been quick because of the same basic engine time after time. Don't be afraid to work it hard, but not continuously hard. Limit your idle time.
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 07 Feb 2019 at 9:10pm
Thanks for all the replies and input, well I got it all back together, used reman injectors, got fuel to the fuel pump and to the injectors, cracked all the lines and fuel dribbled out of each injector, went to start it and it after some cranking it fired up but had no power and while trying to make sure I had no leaks and that the throttle and injection pump cables were on correct it died and would not restart, any ideas? Thanks!
Back to Top
Hurst View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Midway, Ky
Points: 1218 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hurst Quote  Post ReplyReply Direct Link To This Post Posted: 07 Feb 2019 at 9:48pm
Prime it again and if you get it running, crack the injectors one at a time running and let it bleed out for 10 seconds or more. If you had the whole fuel system apart it can be a bear to get all the air out. I’m assuming it was acting like it was starved for fuel and not air. Also check to make sure the cutoff isn’t partially closed on the pump.

Hurst
1979 Allis Chalmers 7000
5800 Hours
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2019 at 2:06pm
Been trying to bleed it repeatedly but still just a little bit of fuel coming out of each injectors and nothing out of the return line on top of pump? Any more advise?
Back to Top
injpumpEd View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Walnut IL
Points: 5110 		Post Options Post Options   Thanks (0) Thanks(0)   Quote injpumpEd Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2019 at 6:52pm
I'm betting the pump is gummed up from sitting. These are 4 plunger pumps, and if 2 are sticking, it will deliver about half the required fuel. Good luck!
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2019 at 8:29pm
Originally posted by injpumpEd injpumpEd wrote:

I'm betting the pump is gummed up from sitting. These are 4 plunger pumps, and if 2 are sticking, it will deliver about half the required fuel. Good luck!
Gotcha, any way of unsticking them or am I looking at removing the pump and going through it? 
Back to Top
injpumpEd View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Walnut IL
Points: 5110 		Post Options Post Options   Thanks (0) Thanks(0)   Quote injpumpEd Quote  Post ReplyReply Direct Link To This Post Posted: 11 Feb 2019 at 12:28pm
Usually getting the pump properly serviced is the best option. Gets it cleaned up and everything clean and happy inside again. 
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 11 Mar 2019 at 2:49pm
Originally posted by injpumpEd injpumpEd wrote:

Usually getting the pump properly serviced is the best option. Gets it cleaned up and everything clean and happy inside again. 
Got it serviced, stuck metering valve, got her to run good now!
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 11 Mar 2019 at 2:50pm
Originally posted by injpumpEd injpumpEd wrote:

Usually getting the pump properly serviced is the best option. Gets it cleaned up and everything clean and happy inside again. 
Got it serviced, stuck metering valve, got her to run good now!
Back to Top
AC 426 power View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 01 May 2012
Location: Ohio
Points: 530 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC 426 power Quote  Post ReplyReply Direct Link To This Post Posted: 11 Mar 2019 at 2:51pm
Got it to run good now and everything, now before I put it hard to work should I do a re torque on the head? Necessary or not?

Edited by AC 426 power - 11 Mar 2019 at 3:13pm
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.113 seconds.


Help Support the
Unofficial Allis Forum