This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


How to replace injectors on a 7010?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
roscoe View Drop Down
Bronze Level
Bronze Level


Joined: 30 Oct 2009
Points: 37 		Post Options Post Options   Thanks (0) Thanks(0)   Quote roscoe Quote  Post ReplyReply Direct Link To This Post Topic: How to replace injectors on a 7010?
    Posted: 25 May 2010 at 9:12pm
My mechanic says that I have a few bad injectors, so I am going to replace them all.

I have a 1980 model 7010.

Is this a straight-forward job, or are there any tricks involved?

Thanks,
Roscoe.
Back to Top
Sponsored Links


Back to Top
Amos View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Ontario
Points: 1318 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Amos Quote  Post ReplyReply Direct Link To This Post Posted: 25 May 2010 at 9:19pm
Quite easy if they all come out without the sleeve.  I have had one come out with the sleeve and it was on a 7010, other than that not hard at all.  You may want to consider having your injection pump at least tested if not overhauled at the same time as the injectors.  Need not buy new just have a reputable shop repair your old injectors.
Back to Top
Adam Stratton View Drop Down
Orange Level Access
Orange Level Access


Joined: 11 Sep 2009
Location: SW MO
Points: 1363 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Adam Stratton Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2010 at 7:54am
It is a pretty simple job.  Make sure and watch if the injectors come up with or without the little copper washer/ fire ring.  If they get lodged in the head, you can use a 5/8 course thread tap to catch them and pull them out.  Be careful not to break them when pulling them out (pull straight with lots of WD-40 or similar), and dont cross thread the lines when putting them back on. 
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20945 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2010 at 7:56am
No copper washers used on 7000-7010-7020-8010.
Back to Top
Adam Stratton View Drop Down
Orange Level Access
Orange Level Access


Joined: 11 Sep 2009
Location: SW MO
Points: 1363 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Adam Stratton Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2010 at 8:16am
Oops.  Sorry!   I just assumed a 7010 had them too.  Thanks for straightening that out for me.  Roscoe would have been digging for those rings for a LONG time.  
Back to Top
roscoe View Drop Down
Bronze Level
Bronze Level


Joined: 30 Oct 2009
Points: 37 		Post Options Post Options   Thanks (0) Thanks(0)   Quote roscoe Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2010 at 9:11am
Thanks, Dr. Allis.   How are they sealed? O-Rings?  Metal seats?
 
Roscoe
Back to Top
Hurst View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Midway, Ky
Points: 1213 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hurst Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2010 at 9:58am
They are sealed with a copper sleeve instead of washers.  By going to the sleeve, it was supposed to keep the injector cooler since the copper was in direct contact with the coolant in the head.

Hurst
1979 Allis Chalmers 7000
5800 Hours
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.074 seconds.


Help Support the
Unofficial Allis Forum