This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
HD6 Steering clutches |
Post Reply |
Author | |
rzee
Bronze Level Joined: 04 Jun 2016 Location: Canada Points: 4 |
Post Options
Thanks(0)
Posted: 05 Jun 2016 at 1:24pm |
My left side steering is not working in forward but a little in reverse, and my right side steering is about 50%. I have replaced the steering clutches 2 years ago because of the same issues. I suspect that the clutches are getting oil on them maybe from a bad engine seal. Has anyone here had a similar problem ? If so, I would to hear of a workable solution.
thanks
|
|
Sponsored Links | |
gemdozer
Orange Level Joined: 17 Sep 2009 Points: 970 |
Post Options
Thanks(0)
|
Did you removed the stering cluch housing plugs for drain and if you have oil in it should came from bevel gear housing and how far are the adjustement stering cluch lever and brake pedal
|
|
Coke-in-MN
Orange Level Access Joined: 12 Sep 2009 Location: Afton MN Points: 41485 |
Post Options
Thanks(0)
|
In bottom of case are holes threaded for 3/4" pipe plugs . be sure when running the machine they are OUT unless running in water .
Put in plugs - fill case with aprox 4 gallons of diesel or stoddard solvent - run machine back and forth pulling clutches and applying brakes - then put catch pan under machine and remove plugs Operate machine again but not under load of working until clutch plated dry out . Other thing is remove clutch packs - replace friction material with HD11 ceramic bi-metal clutch plates . |
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful." |
|
Dozer
Orange Level Joined: 16 Aug 2011 Location: SW New York Points: 689 |
Post Options
Thanks(0)
|
I have had a bad experience washing the clutch packs with diesel. Mice were living in the steering clutch compartment. The combination of diesel and mouse nest made a big mess. Since then I check thru the 3/4 drain opening that the steering clutch compartment is free of mice.
Mouse pee can freeze up a clutch pack quickly. Mice enter via the brake operating rod opening. I fabricated a replacement for the rubber bellows using the plastic from a 5 gallon oil pail. |
|
rzee
Bronze Level Joined: 04 Jun 2016 Location: Canada Points: 4 |
Post Options
Thanks(0)
|
I am running with the plugs in. I'll try pouring solvent in there and clean the clutches and run without the plugs. Where would the oil come from as the engine is far from the steering clutches?
|
|
CAL(KS)
Orange Level Joined: 18 Sep 2009 Location: Chapman, KS Points: 3786 |
Post Options
Thanks(0)
|
if you have oil in your dry clutch housing its likely from the bevel gear shaft seal/compartment
|
|
Me -C,U,UC,WC,WD45,190XT,TL-12,145T,HD6G,HD16,HD20
Dad- WD, D17D, D19D, RT100A, 7020, 7080,7580, 2-8550's, 2-S77, HD15 |
|
Dozer
Orange Level Joined: 16 Aug 2011 Location: SW New York Points: 689 |
Post Options
Thanks(0)
|
Both sides of the steering clutch compartment contain oil. Oil in the steering clutch compartment will effect the brake band more than the steering clutch. Are the steering clutches slipping or are they not disengaging?
|
|
rzee
Bronze Level Joined: 04 Jun 2016 Location: Canada Points: 4 |
Post Options
Thanks(0)
|
The brakes are working fine. The steering controls little or no effect on the direction of travel. Currently I can only drive forward and reverse and if I am on a mound perpendicular to the tracks, then I am able to turn using the brakes. I removed the plugs and there seems to be lots of oil in the right side compartment but the left side is dry. I will pick up some solvent tomorrow and try the washing process.
|
|
gemdozer
Orange Level Joined: 17 Sep 2009 Points: 970 |
Post Options
Thanks(0)
|
You should have on top stering cluch lever 1 to 3 inchs free travel and the brake pedal should have 1 3/4 to 2 inchs free play on HD6
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |