This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
working on the "A" Gleaner today |
Post Reply |
Author | |
Don(MO)
Orange Level Joined: 12 Sep 2009 Location: Bates City MO. Points: 6862 |
Post Options
Thanks(0)
Posted: 24 Sep 2009 at 7:06pm |
Here is a pic of the A Gleaner's in sides, straw walkers, cob cover for the rattle chain and the like.
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Sponsored Links | |
Don(MO)
Orange Level Joined: 12 Sep 2009 Location: Bates City MO. Points: 6862 |
Post Options
Thanks(0)
|
I didn't get the last part in. so here it is. The last two pics are the home made wires for the straw walkers. What do you think of them?
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Eric[IL]
Orange Level Joined: 14 Sep 2009 Location: Illinois Points: 485 |
Post Options
Thanks(0)
|
Your new cob cover under the end of the rattle doesn't block the primary fan air, does it? Or, maybe I am just thinking about how the early K gleaners have the 2 fan setup - maybe E gleaners also had 2 fans?? Can't remember.
Also, I think it is interesting how your A's shoe front fins direct all the grain towards the middle of the sieve & chaffer. I am thinking the E & K has these fins in straight?
|
|
Don(MO)
Orange Level Joined: 12 Sep 2009 Location: Bates City MO. Points: 6862 |
Post Options
Thanks(0)
|
Eric, The pic just makes the cover look like it's blocking the fan off. This is how the install pic from Gleaner said to set it. I'm not to good a this pic thing. lol
The bad thing about the way fins flow is all the flow is to the middle and not to all three walkers.
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Skyhighballoon(MO)
Orange Level Joined: 11 Sep 2009 Location: Pilot Grove, MO Points: 3115 |
Post Options
Thanks(0)
|
Eric - good questions. My EIII is a double fan and it looks like the E is too from the parts book. I just looked in a cornhead parts book and see PN 559222 cob shield for my EIII. Maybe mine's already in and I didn't realize it. Will have to look closer again next trip.
Don - did you solder every one of those homemade wires in or use a MIG? Looks good! Mike |
|
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330 1969 180 gas 1965 D17 S-IV gas 1963 D17 S-III gas 1956 WD45 gas NF PS 1956 All-Crop 66 Big Bin 303 wire baler, 716H, 712H mowers |
|
Don(MO)
Orange Level Joined: 12 Sep 2009 Location: Bates City MO. Points: 6862 |
Post Options
Thanks(0)
|
Mike, No I didn't do it Dad did it for me, He's a good man to have around for that soldering. Dad has a sheet metal shop in my shop and make my job on this ez. LOL
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Don(MO)
Orange Level Joined: 12 Sep 2009 Location: Bates City MO. Points: 6862 |
Post Options
Thanks(0)
|
I need to say the pic makes the hole look like it's covered up, There is 6" behind it and 4" under it and the cover can be set up or down.
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |