226 oil system question.

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Guy brought me a 226 motor in a box and asked if could build him a pulling engine for his wd45. After examining everything i believe the block is a d17, the crank is 5.75, the bore is 4.50. Not a bad start. My question is someone installed the cam bearings but the center bearing only has one oil hole that is going to the center main. The main feed passage is blocked. I'm wondering if someone was intending to change the oil system to be priority main oiling. Has anyone done this?

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Topic: 226 oil system question. Posted: 27 May 2020 at 8:34pm
	Guy brought me a 226 motor in a box and asked if could build him a pulling engine for his wd45. After examining everything i believe the block is a d17, the crank is 5.75, the bore is 4.50. Not a bad start. My question is someone installed the cam bearings but the center bearing only has one oil hole that is going to the center main. The main feed passage is blocked. I'm wondering if someone was intending to change the oil system to be priority main oiling. Has anyone done this?

Sponsored Links

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20525	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 10:19am
	On a "full-flow" oiling system all three cam bearings are the same. On the old cotton string filter system the center cam brg has 2 holes. D-17 engines have 3 inch main brgs. WD45 mains are smaller at about 2.500" or so. Edited by DrAllis - 28 May 2020 at 10:20am

danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 11:28am
	The block and crank have 3 inch mains. Does the cam serve as the main oil gally?

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20525	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 12:26pm
	Hollow camshaft is indeed the main oil galley. That is why it is so important to have good cam bearings for decent oil pressure. Are you a PH8A filter (full flow) or cotton string filter ??

danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 12:36pm
	Judging by the filter base that's in the box of parts i assume it would be a ph8a type of filter. The cam should be fed oil via the center cam bearing, correct?

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20525	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 3:10pm
	Yes. Then, the front and rear mains receive their oil from the camshaft. Pretty simple design and the block was easier and cheaper to cast without a main oil galley.

danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Posted: 28 May 2020 at 4:20pm
	Thank you.

danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Posted: 29 May 2020 at 8:23pm
	Dr.Allis one more question. Would know the intake lobe center line for the 175 cam?

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20525	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 29 May 2020 at 8:54pm
	I come up with 112.5 degrees for both the 170 and 175 cam which are a different grind from each other. I have a good friend in Ohio who told me trying to alter a 175 cams timing doesn't work well at all. He says A-C has that thing tuned about as well as it can be and still be able to lug down to 900 RPM peak torque. I have never tried anything other than OEM timing for the 175 cam even before he told me that.

danno067 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 29 Jul 2019 Location: Wisconsin Points: 12	Post Options Post Reply Quote danno067 Report Post Thanks(0) Quote Reply Posted: 29 May 2020 at 9:20pm
	Could you tell me what you think of these specs? Cam specs. @ .050 lift Ex lobe lift .322 valve lift. .595 duration 239 Ex open 45 bbdc Ex close 14 atdc Ex C.L. 106 In lobe lift .320 valve lift .592 duration 238 In open 9 btdc In close 49 abdc In C.L. 108 Engine specs. 4.560 bore 5.750 stroke Comp. Is 13.5:1 static 1.95 intake valve 1.64 exhaust valve 1.85 rocker ratio Cam was degreed with stock timing gears. Edited by danno067 - 29 May 2020 at 9:23pm

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20525	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 29 May 2020 at 9:50pm
	I have no opinion on the grind. I have used a 175 cam that was ground for more lift. I think it was .460" stock valve lift and it was changed to .560" lift. Timing/duration numbers were to remain the same as OEM. I can't say that it made a huge difference and I simply do not have the time or patience to try five different camshafts looking for that "pot-of-gold" at the end of the camshaft rainbow. This cam was used in stock RPM and 30% over RPM classes. This much I can tell you. I built two identical 360 cube engines 25 yrs ago one winter. Same bore/stroke, camshaft (175) and carb (D-19). The only difference was one had oversized valves (existing customer head freshened up) and the other stock valves with shortened up intake guides. When each was run on the dyno there was no difference in their HP output !! and I would bet the small valve engine would lug a bit lower before stalling. Ignition timing always works best at 18 to 22 degrees BTDC on my engines. Edited by DrAllis - 29 May 2020 at 9:51pm