This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


185 power steering cylinder
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Allis_Cooper View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 05 Oct 2021
Location: FL
Points: 27 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis_Cooper Quote  Post ReplyReply Direct Link To This Post Topic: 185 power steering cylinder
    Posted: 8 hours 4 minutes ago at 9:36am
Anyone on here have any experience disassembling the power steering hydraulic cylinder on an AC 185? There does not appear to be a cap that screws off nor do I see any snap rings.

Wink Someone on this forum will know the secret, they always do.
Back to Top
Sponsored Links


Back to Top
ac-mike View Drop Down
Silver Level
Silver Level


Joined: 14 Sep 2009
Location: Kentucky
Points: 279 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ac-mike Quote  Post ReplyReply Direct Link To This Post Posted: 7 hours 27 minutes ago at 10:13am
Tap head back inside enough to remove snap ring then pull out
D-12III, 200D, 170G, HD-3, D19D 3pt, D17D High Crop, WD45G p/s, D15IID, D15IIG, D15G IND, 655, (3)WD45D p/s, 700, 816
Back to Top
Allis_Cooper View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 05 Oct 2021
Location: FL
Points: 27 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis_Cooper Quote  Post ReplyReply Direct Link To This Post Posted: 4 hours 28 minutes ago at 1:12pm
Worked like a charm! You guys always know the answer.

The pressed in outer seal around the shaft was a bear to get out!

Installing seal kit  70255712-5 from DJS Tractor.
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22255 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 3 hours 30 minutes ago at 2:10pm
Before installing piston back into the barrel, wrap the new teflon piston seal with two wraps of paper and place a radiator hose clamp around the teflon seal and compress it. I'd wait overnite if it was mine and remove the clamp, grease/oil lightly and stick it slowly into the barrel. If you don't do this, chances are pretty good you will cut the new piston seal.
Back to Top
Allis_Cooper View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 05 Oct 2021
Location: FL
Points: 27 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis_Cooper Quote  Post ReplyReply Direct Link To This Post Posted: 30 minutes ago at 5:10pm
Thanks for the advice on that.

When I took the piston off the tractor the spherical swivel joints on either end fell out in my hand and some of the joint housing cracked off. Unfortunately, the only replacement with the correct dimensions I've found so far are from A&W Tractor  Part Number: 244019V $136 each!!

If anyone knows of  another source please let me know. They seem to be .3/4" ID and 1 5/8" OD.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.055 seconds.


Help Support the
Unofficial Allis Forum