This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


190xt harmonic balancer removal question
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
youngorange2000 View Drop Down
Silver Level
Silver Level


Joined: 27 Mar 2019
Location: eastcentral MN
Points: 308 		Post Options Post Options   Thanks (0) Thanks(0)   Quote youngorange2000 Quote  Post ReplyReply Direct Link To This Post Topic: 190xt harmonic balancer removal question
    Posted: 06 Oct 2022 at 3:29pm
I need to remove the front cover on my xt. The problem is all of the harmonic balancer puller tools in town are too small. Would it be safe to remove with a three jaw puller? Any suggestions would be appreciated
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 19576 		Post Options Post Options   Thanks (1) Thanks(1)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2022 at 6:01pm
NOOOOOO !!!! You CANNOT pull on the O.D. of any rubber isolated crankshaft pulley !!!  Make yourself a puller:  You goal is to pull from three of the six holes on the center hub. Use a 1 inch thick plate. Drill your holes to match three of the hub holes. Drill a 1 inch+ hole dead center. Use a 1 inch fine thread bolt and nut to tack weld under the center hole area. Use grade 8 bolts (7/16") long enough to position the 1" NF on the push side of the plate. Loosen the crankshaft bolt 2 full turns and press against the head of it. It sometimes takes 10 TONS of pressure to get it loose. Make the plate big enough you can drill three more holes for the 426 engine and have one tool for both.

Edited by DrAllis - 06 Oct 2022 at 6:02pm
Back to Top
DougG View Drop Down
Orange Level
Orange Level


Joined: 20 Sep 2009
Location: Mo
Points: 7946 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DougG Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2022 at 6:31pm
And they pop when they finally let go !
Back to Top
wildcat2 View Drop Down
Bronze Level
Bronze Level


Joined: 03 Aug 2011
Location: United States
Points: 104 		Post Options Post Options   Thanks (1) Thanks(1)   Quote wildcat2 Quote  Post ReplyReply Direct Link To This Post Posted: 07 Oct 2022 at 7:25am
Dr. Allis your reply should probably be posted in the knowledge section for prosperity.
Back to Top
JPG AUSTRALIA View Drop Down
Orange Level
Orange Level


Joined: 13 Sep 2009
Points: 733 		Post Options Post Options   Thanks (2) Thanks(2)   Quote JPG AUSTRALIA Quote  Post ReplyReply Direct Link To This Post Posted: 08 Oct 2022 at 12:07am
Wildcat2 I think that most of dr allis answers should be archived in the knowledge section.😀
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.046 seconds.


Help Support the
Unofficial Allis Forum