![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Removing equalizer pin |
Post Reply ![]() |
Author | |
7060 ![]() Orange Level ![]() ![]() Joined: 16 Sep 2009 Location: Missouri Points: 1142 |
![]() ![]() ![]() ![]() ![]() Posted: 10 May 2018 at 1:14pm |
I have a broken equalizer pin on my hd11e. Took the clutch tank off and pulled the front part of the pin out, but the back half it stuck. Has anyone got a trick to pulling it out? I build a puller but no luck yet.
![]() |
|
![]() |
|
Sponsored Links | |
![]() |
|
Tad Wicks ![]() Orange Level ![]() ![]() Joined: 27 Mar 2011 Location: Shandon, CA Points: 2160 |
![]() ![]() ![]() ![]() ![]() |
I don't remember what is behind it, how much is left? how deep is it? If it is open on the back side sometimes you can burn a hole through the center of a stuck pin then quench it and it will come out without much work. If you can't reach it with a torch an airarc works well, be prepared for lots of blow back. Tad
|
|
![]() |
|
donoman ![]() Silver Level ![]() Joined: 18 Feb 2015 Location: New Zealand Points: 117 |
![]() ![]() ![]() ![]() ![]() |
At the back of the pin there is a pivot pin retaining plate ,held by 2 1/2 inch cap screws on the pin and 1 capscrew on the crossmember. you should be able to drive the pin back and out, or push it through to the front with the weight off it. this pin is common from the HD9 to the late 11B'S
|
|
![]() |
|
Ian Beale ![]() Orange Level ![]() Joined: 03 Oct 2011 Location: New South Wales Points: 937 |
![]() ![]() ![]() ![]() ![]() |
How did THAT get broken?
|
|
![]() |
|
7060 ![]() Orange Level ![]() ![]() Joined: 16 Sep 2009 Location: Missouri Points: 1142 |
![]() ![]() ![]() ![]() ![]() |
I built a puller that attaches to the 2- 1/2β bolt holes. After replacing the 2x4s with square tubing, and heat from a rosebud and a 4lb hammer I got it to move 1 1/2β. Do they all come out this hard? When it goes back in itβs getting anti seize. I have no idea why it would break where it did anyways. It broke 3β into the tube. Having a machine shop make one out of 4140 steel shaft.
|
|
![]() |
|
DiyDave ![]() Orange Level Access ![]() ![]() Joined: 11 Sep 2009 Location: Gambrills, MD Points: 50759 |
![]() ![]() ![]() ![]() ![]() |
Are you sure you have relieved all the pressure, on that pin? If it still has weight/tension on it, in some way, it may get dangerous, as it comes out...
|
|
![]() |
|
7060 ![]() Orange Level ![]() ![]() Joined: 16 Sep 2009 Location: Missouri Points: 1142 |
![]() ![]() ![]() ![]() ![]() |
The front piece of pin that was in the equalizer pulled out easily with a pry bar. I ended up hooking a chain and a 4x8 hydraulic cylinder to it and the drawbar and got it pulled out.
|
|
![]() |
|
donoman ![]() Silver Level ![]() Joined: 18 Feb 2015 Location: New Zealand Points: 117 |
![]() ![]() ![]() ![]() ![]() |
Yes 4140 would be what I would use for a new pin
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |